Call Me FreeCall Me Free Send SMS
+918061856722
Home » Products » Slitting Lines » CR Slitting Line

CR Slitting Line

CR Slitting Line
CR Slitting Line
Send Inquiry
Product Code : 02
Product Description

Cold Rolled Steel Sheet Slitting Line

CR SLITTING LINE SLCR 500-1600

Line Composition

  • Coil car

  • Double Opposed Expandable Drum Uncoiler

  • Coil Opening device

  • Pinch Roll

  • Shear

  • Guiding device

  • Pinch Guide

  • Slitting machine

  • Waste Selvage device (scrap reels device)

  • Loop Table

  • Tensioner and Line Separator

  • Deflector Roll

  • Recoiler with Pusher Plate

  • Over Arm Separator

  • Out Board Support

  • Coil Car

  • Electrical Panels & hydraulics.

Working Process

CR coil is loaded on the Coil Car by overhead crane. The coil car travels on rail lines by AC motor & brings the coil to the uncoiler. The lifting cylinder of the coil car centralizes the coil to the Uncoiler centre. The two opposed bodies of the uncoiler are mover towards each other so that the collapsed drums of both the bodies enter the ID of the coil. After proper positioning, the drums are expanded to hold the coil firmly. The coil car is lowered and taken back.

The uncoiler drive rotates the coil and brings the leading end in the feeding position. Snubber roll in lowered on the coil and the coil straps are cut. With the operation of peeler table & uncoiler drive, the leading end is fed in the Pinch Roll. The pinch roll is pressed and the drives of uncoiler & pinch roll take the leading end forward though shear. The end is cut if required. The leading end is further moved through vertical guides in to the slitter. As the slitter motor accepts the leading end, the pinch roll & snubber rolls are taken up.

Slitter takes the strip further but now in slitted condition. All the slits are taken forward over the roller table & loop table, through line separator, pressure pad & deflector roll in to the Recoiler drum where the ends are inserted in the gripping slot. The ends are properly positioned in the slot as per the setting of Over Arm Separator and the drum is expanded.

The slitter and recoiler drives are inched forward together and a couple of turns are loosely wound over the drum. The pad is put in operation, loop table is removed back and slitter drive takes the slits in the loop. The Out Board support is brought in position to support the out board end of the recoiler shaft. The line is put in RUN mode. The recoiler tightens the turns against the resistance of the pressure pad and the winding goes on. Both slitter & recoiler drive run in synchronization to keep the line speed constant and the strips are kept loose in the loop. As the coil builds up on the recoiler drum, its rpm goes down to keep the line speed constant. The same is effected by the speed sensing at the deflector roll by a rpm sensor. The over arm separator keeps moving up with the built up by a special hydraulic valve maintaining a set pressure on the coil.

The line goes on until the coil is completely wound over the recoiler drum. The trailing ends are clamped over the slit coils and overarm separator is lifted. The exit coil car is brought below the coil and lifted to support the coil weight. The out board support is removed. The drum is collapsed and the pusher plate is operated along with the coil car to take the coil smoothly out of the drum.

The slitted coils are removed by the overhead crane and the line is ready for the next coil.

Technical Specifications :

Model Number

Width (mm)

Thinckness (mm)

Speed

SLCR-700

700

0.5-2.0

80-150 MPM

SLCR-1250

1250

0.5-3.0

80-150 MPM

SLCR-1600

1600

0.5-3.0

50-150 MPM




EFFIMAC EQUIPMENT PVT. LTD.
X


Back to top